WillCo Drilling Intelligence

Field Review 2, November 2026
Proof Is What You Measure After the Job
📋 This Review at a Glance
Covers developments disclosed October 1-31, 2026 | 13 feature stories and 7 field briefs, all four grades | 5-minute skim: this table, the 🎯 lines and the checklist
🟢 A: a documented field observation, including negative or partial outcomes. 🔵 B: a limited field trial with unresolved attribution or transferability. 🟡 C: laboratory, modeling or review evidence for the claim assessed. 🟣 U: the available reporting is insufficient to verify the specific claim or reproduce its comparison; U does not mean false. Grades describe evidence scope, not vendor quality or guaranteed performance in another well.
📩 To discuss a scoped technical review of a cementing or casing-repair program, contact WillCo Drilling Consulting at info@willcodrilling.com.
🧱 Top Story: Cement Where the Margin Runs Out
Two cementing papers from SPE ATCE attack the same problem from opposite ends: a margin too narrow for a conventional job. One changes where the returns travel; the other manages pressure through placement and engineers the slurry for the heat.
Figure 1 matches each kind of evidence this issue's grade A cement and repair jobs reported to the question it answers, from placement records to in-service response.

🟢 A | Norway: inner-string cementing sets two strings with no losses inside the fracture gradient
What carries the grade: two cement jobs with no losses during placement, and cement bond logs the authors read against the NORSOK D-010 requirement.
OKEA and SLB, with Three60 Energy, report in SPE-233957-MS (SPE ATCE) that they cemented an 11-3/4-in. and a 9-5/8-in. string on the Norwegian Continental Shelf (NCS) with no losses, on strings where conventional cementing "would substantially exceed the prognosed fracture gradient". The authors describe it as the first use of such an inner-string configuration to set a qualified primary barrier on the NCS, run from a semi-submersible in mid-winter.
The plan combined fluids, geomechanics and placement, and one element moved the returns path. Cement went down an inner string, and returns came back through a casing-mounted sliding-sleeve port into the casing-to-drillpipe annulus, bypassing the casing-to-casing annulus to reduce the equivalent circulating density (ECD). Before the casing ran, the well was displaced to an ultra-low-rheology non-aqueous fluid (NAF) weighted with micronized barite.
🎯 No losses on either string, and the authors report that cement bond logs (CBL) confirmed isolation beyond the NORSOK D-010 requirement of two intervals of about 98 ft each.
🟢 A | Hungary: nine ultra-HPHT strings at up to about 464°F, backed by log, playback and stimulation
What carries the grade: nine wells cemented, with post-job logs, pressure playback and stimulation results on the detailed case.
SLB cemented production strings in nine Hungarian wells with a pore-fracture margin as low as 0.07 s.g., about 0.58 ppg, it reports in SPE-233873-MS, a paper whose title calls them "Europe's Most Extreme Wells". Static bottomhole temperature reached up to about 464°F, with circulating bottomhole temperature above about 410°F and bottomhole pressure above 16,000 psi.
The design combined real-time managed pressure cementing (MPC), a high-density cement with an optimized particle-size distribution, and a thermally stable spacer compatible with synthetic-based mud (SBM).
🎯 In the detailed case, the proof came after the job: CBL combined with pressure playback confirmed placement, no sustained casing pressure (SCP) appeared, and, the authors write, the stimulation that followed "further proved zonal isolation across multiple stages".
🔩 Casing: A Shoe Track With Its Checks Built In
🟢 A | Saudi Arabia: a wet shoe track with planned pressure checks adds 300 ft of effective lateral on a 27,536-ft string
What carries the grade: one field installation and cementation, with pressure checks after placement.
Saudi Aramco and Baker Hughes report the first engineered wet shoe track long-string completion in an unconventional carbonates area of interest, in SPE-234172-MS. The authors report that the integrated shoe track run added 300 ft of effective lateral for hydraulic fracturing, with pressure checks planned into the plug train, and plan to make the integrated shoe track tool (IST) the default completion for all development wells in the area.
The plug train ran in three steps: a "750 psi wiper plug ahead of cement, 3,000 psi wiper plug behind cement, and 5,000 psi behind the wet shoe volume". The 120 ft of shoe track around the IST was left wet by design with a 5-bbl volume of retarded water.

The 673-joint, 5-1/2-in. string reached 27,536 ft with the IST, rotating at 15 to 25 rpm, with a mud-over-air flotation sub 1,000 ft inside the lateral.
🎯 The checks after placement: rupture-disk behavior was confirmed by raising pressure to 4,400 psi; a 3,000-psi casing test was performed against the bumped third plug, and the completion was pressure tested to 3,000 psi for 30 minutes.
🛠️ Remedial Work: Squeeze and Patch
🟢 A | Indonesia: tight rock that took under 1 bbl, and microfine squeezes that held 300 psi
What carries the grade: two wells, injectivity tests before the squeeze and pressure tests after placement.
NPS Energy Indonesia, part of National Energy Services Reunited (NESR), reports in SPE-234406-MS (SPE APOGCE) two squeeze jobs in very tight formations onshore North Sumatra that followed "repeated squeeze cementing failures using Class G cement". The authors turned to microfine cement, which they say penetrates "microannuli inaccessible to Class G cement".
The injectivity tests showed how little the rock would take, and on both wells pressure fell off less than 100 psi in 15 minutes.
Well A: pressure rose immediately to 350 psi at 0.5 bpm and the rock took 0.63 bbl; a 1-bbl microfine squeeze was placed, tagged and drilled out.
Well B: maximum 450 psi, and the rock took 0.21 bbl; the microfine placement covered two perforated intervals.
🎯 The pressure tests: Well A held 300 psi after drill-out, and each of two perforated intervals in Well B held 300 psi for 5 minutes.
🟢 A | North Kuwait: three metal-to-metal patches repair a 186-ft damaged interval and stop the water
What carries the grade: production results after the repair; the "record-length" claim is a U, with no patch length or reference given.
Kuwait Oil Company (KOC) and Weatherford report in SPE-234528-MS (SPE APOGCE) repairing a 9-5/8-in. casing in an Upper Zubair producer with a long integrity failure between 8,323 and 8,509 ft, a 186-ft interval.
The repair used three tubular patch assemblies (TPA) with hydraulically expanded metal-to-metal seals.
🎯 Sustained casing pressure eliminated, water influx stopped and stable dry-oil production restored, with near-full bore kept across the repaired section, the authors report.
🌀 Drilling the Narrow Window
🟢 A | Oklahoma: MPD cuts final-trip time 74% to 90%; the conventional casing landed 968 ft short
What carries the grade: four wells on two adjacent pads with logged trip, reaming and cost data. The baseline is one conventional well.
Opla Energy Services and Devon Energy compare managed pressure drilling (MPD) with conventional drilling in the Woodford Shale, Canadian County, Oklahoma, in SPE-233915-MS. Four wells on two adjacent pads drilled the 8-3/4 by 8-1/2-in. interval through a pressure window of 0.4 to 0.8 ppge: one conventionally and three with MPD.
The conventional well ran 11.8 to 12.0 ppg active mud weight, raised to 12.4 to 12.5 ppg after wellbore instability and a gas influx, and its 5-1/2-in. casing landed 968 ft short of planned total depth (TD). The MPD wells targeted an ECD near 12.4 ppg.
🎯 Against the conventional well:
Final-trip time: from 15.68 to between 1.55 and 4.14 hours per 1,000 ft on the final trip, measured from bottoms-up at TD to casing landed, 74% to 90% lower.
Reaming: on the final trip, from 8.18 to 1.33 hours per 1,000 ft on the MPD well sharing the pad and rig; none on the two wells on the neighboring pad. Interval reaming time was 59% to 73% lower.
Cost: the authors' cost per lateral foot fell from $22.47 to between $13.32 and $19.85, 11.6% to 40.7% lower, with fluid cost 6.4% to 37.2% lower. The abstract does not itemize it, so read it as a per-foot comparison, not total well cost.

⚙️ Drillstring Mechanics: What the Bit Feels
🔵 B | Sichuan-Chongqing: a damper cuts vibration 47% to 62% on one trial well
What carries the grade: one field trial against offset wells, with a validated model.
Authors from CNPC Daqing Drilling Engineering and Southwest Petroleum University report a field trial of a multidirectional damper in Well Yang 101X2, Shiniulan Formation, over about 10,827 to 13,451 ft, in Processes on October 26.
🎯 Lateral vibration fell 47%, axial 62% and torsional 61%, rate of penetration (ROP) rose 48% against offset wells, and more than 80% of cutters stayed intact.
Their coupled-vibration model, validated against measured data from a well on the Yang 101 platform, put the optimal damper-to-bit distance at about 246 ft for an 8-1/2-in. bit and about 164 ft for 12-1/4 and 16-in. bits; in the horizontal section, the best position was between the stabilizer and the drill collar. For the trial itself, pre-run simulations placed the damper in a sweet-spot window within about 164 ft of the bit.
🟡 C | China: stick-slip measured downhole, an estimated 350 rpm against 120 rpm at surface
What carries the grade: one downhole field measurement (the estimated bit speed and the stick-slip cycle) used to calibrate a finite element (FE) model; the weight and speed trends are model results, and no mitigation was tested in the field.
Stick-slip was measured downhole in an ultra-deep vertical well drilled with a polycrystalline diamond compact (PDC) bit of about 13-1/8 in., and the measurement calibrated a nonlinear FE model, report authors from Shanghai University and the Sinopec Research Institute of Petroleum Engineering in Scientific Reports on October 23.
🎯 The maximum estimated downhole speed was about 350 rpm against 120 rpm at surface, in a cycle of about 10 seconds: about 3 s stuck and 7 s slipping.
In the model, stick-slip severity rose from 0.52 to 1.46 as weight on bit (WOB) rose from about 13,500 to 36,000 lbf at 120 rpm, and fell from 1.75 to 0.78 as rotary speed rose from 60 to 160 rpm at about 27,000 lbf.
💎 Bits and BHA: Read the Limiter, Read the Dull
🟢 A | Browse Basin: a bit and BHA redesign nearly doubles the reservoir-section rate
What carries the grade: a five-well subsea campaign measured against a basin record built from more than 45 wells; the abstract does not say whether the rates are on-bottom or total.
A bit and bottomhole assembly (BHA) redesign nearly doubled the 8-1/2-in. reservoir-section rate of a Browse Basin subsea campaign against a basin record based on more than 45 exploration and development wells, report Shell Australia, Shell Exploration & Production Company, SLB Australia and Ray Procter Group in SPE-234488-MS at the SPE Asia Pacific Oil & Gas Conference.
The team applied its Challenge the Limit (CTL) workflow, which starts by listing performance limiters and then designs them out where that is economic.
Limiters: on weight on bit downhole, the bit's structural limit, BHA buckling, the jar transition and BHA weight; at surface, solids-control capacity.
Design changes: stabilizers redesigned and repositioned to minimize lateral vibration and widen the weight-on-bit envelope; gauge pad geometry, cutter backrake and nozzle hydraulics optimized to mitigate the key risks in each formation.

The authors describe the trade-offs: extra BHA weight buys weight on bit but costs torque and drag, and cutting-structure efficiency while unworn has to be balanced against fracture resistance where formation interfaces are severe.
🎯 The new benchmark of about 102 ft/hr held across the typically abrasive Plover and Nome formations.
🟢 A | Asia Pacific: shaped PDC cutters, and the backup element that never engaged
What carries the grade: four field cases in three countries, each compared with offsets, read from the dull condition, or inspected for cutter engagement.
Field Review 1 ranked cutter shapes in granite in the lab; this month, four field runs. Halliburton and PT Pertamina Hulu Rokan report four field applications of shaped PDC cutters in SPE-234561-MS, also at the SPE Asia Pacific Oil & Gas Conference. Three runs beat their offsets or came out with little dull damage, and the fourth showed a backup element that never engaged.
Indonesia: an 8-1/2-in. bit with Shape 1 cutters drilled about 1,093 ft of hard carbonate, interbedded and metasedimentary rock to TD in one run at about 82 ft/hr on-bottom ROP, about 46% faster than the previous fastest offset.
Thailand: a four-bladed rotary steerable system (RSS) bit with mixed Shape 2 and Shape 3 cutters, replacing an established five-bladed design, drilled about 2,346 ft at about 213 ft/hr on-bottom through a simultaneous drop and turn, with no significant dull damage on the shaped cutters.
Australia, 6-1/8-in. RSS run: a 6-1/8-in. RSS-compatible bit with Shape 1 cutters drilled about 3,009 ft, an indicated 20% improvement versus offset, with predominantly low recorded vibration.
🎯 In a single-bit motor run of about 8,524 ft through a long production section in Australia, the active Shape 2 cutters in the cone showed acceptable durability, but the Shape 2 backup element did not engage at the depth of cut the bit actually saw.
🌋 Geothermal and the Frontier
🟢 A | North China: a stimulated geothermal well reaches a maximum tested discharge of about 2,300 bbl/d against a target of about 6,040
What carries the grade: a post-stimulation pumping test at three pump speeds, compared with a model ensemble. A negative result, reported as such.
Well 960, a stimulated carbonate geothermal well in the Houcheng Basin of the Beijing piedmont, produced well short of its target in its post-stimulation pumping test, report authors from China University of Petroleum (Beijing) and the Hebei Fourth Brigade in Energy Science & Engineering on October 6. The well produces from Mesoproterozoic Jixianian dolomite.
🎯 Raising pump frequency from 30 to 37 Hz increased discharge 24%, but drawdown rose 179% and specific capacity fell 56%. Maximum tested discharge was about 2,300 bbl/d, versus a project target of about 6,040 bbl/d; the test maximum is not an established sustainable operating rate.

At 33 and 37 Hz, end-stage drawdown exceeded the upper bound of the reference-model ensemble by about 98 and 169 ft. The authors report increasing excess head loss at higher pumping intensities and describe some fractures partly filled with carbonate cement and solid bitumen as geological context for limited hydraulic effectiveness; the test measures integrated head loss and does not separate wellbore, near-wellbore and reservoir losses. In their words, "geometric fracture development does not necessarily correspond to hydraulic effectiveness". They recommend assessing reservoir effectiveness before drilling.
🟡 C | Superhot geothermal (follow-up): Quaise aims for 700°F while the field proof is still open
What carries the grade: C covers the review's synthesis and model scope, including the field milestones it summarizes; U covers Quaise's target performance, which is still a plan.
Field Review 1 covered Quaise's DOE selection for Project Obsidian. A review in Energies by Mina S. Khalaf, published October 2, concludes that durable reservoir-scale circulation at or above about 707 to 752°F "remains an active area of field validation". The review cites propped interwell circulation at Newberry at about 628°F as a field milestone.
🎯 In an October 26 video, Quaise said the team is "drilling this well to 15,000 feet and 700 degrees Fahrenheit" at Project Obsidian; a later injector-producer flow test aims at "10 to 15 megawatts of electricity production potential". Nabors lists a PACE-B rig deployed at Project Obsidian in its October 27 results deck.
⏱️ Records Without a Clock
🟣 U | Lower 48: two Nabors drilling records without a stated clock basis
What carries the grade: two described records without the clock definition (on-bottom or total), the comparator population or the baseline needed to compare them.
Nabors said in its third-quarter results on October 27 that its rigs "helped two Lower 48 operators achieve new drilling records". The North Dakota record came from a PACE-B, the rig class Nabors lists on Project Obsidian.
🎯 A PACE-B rig in North Dakota drilled "more than 27,600 feet in 148 hours", "nearly 187 feet per hour". A PACE-X rig in South Texas drilled an "18,500-foot well in under six days, averaging more than 3,200 feet per day", and the operator "recorded its fastest drilling performance in the basin to date".
📌 In Brief
Your move lines are WillCo analysis.
🟣 U (time and cost benchmark) | Perenco UK: two Southern North Sea subsea P&As from a jackup: Perenco UK said on October 19 that it and Petrodec plugged and abandoned the Leman South (53/02a-15Y) and Durango (48/21a-4z) wells and removed the associated subsea infrastructure in a single campaign from the HAEVA jack up vessel, "to the agreed timeframe", with no per-well days or costs published. 🎯 Your move: compare barrier scope, well access, infrastructure removal, mobilization and weather exposure before normalizing campaign time or cost; the release does not establish a per-well efficiency benchmark.
🟣 U | Weatherford: six high-temperature sections shoe to shoe, Thailand: Weatherford's third-quarter results (October 20) report that its Magnus Saker drilling system drilled six high-temperature sections in single shoe-to-shoe runs, a campaign that "eliminated an additional drilling assembly trip" and "saved over 100 operational hours". 🎯 Your move: ask for the section temperatures, hole sizes and trip assumptions behind the hours.
🟢 A | CNPC: Cambrian core from about 26,509 ft, Tarim Basin: CNPC recovered about 20 ft of continuous core from about 26,509 ft at the Zhentan-1 well in Cambrian source rock, the first core of its kind from below about 26,250 ft on the basin's northwestern margin, Drilling Contractor reported on October 7. 🎯 Your move: for ultra-deep exploration, tie the coring run to the decision it must inform, and confirm the recovered core represents the interval before it carries that decision.
🟢 A (negative) | Sidewall cores in laminated sands, six wells: Uğur Paköz (JPEPT, October 31) reports only 25 sandy plugs from 294 attempted depths in thinly laminated unconsolidated sands; most of the recovery came from clay-rich laminations, not reservoir sand. 🎯 Your move: set a recovery acceptance criterion before the run and plan a conventional core where laminations are thin.
🟢 A (partial) | Welltec and Equinor: CT fish top retrieved on wireline: an electric-line run cut and retrieved the spiral top of more than about 3,280 ft of coiled tubing (CT) left in the well by an unsuccessful CT intervention; the mill run to dress the remaining fish failed on the residual bend in the CT (SPE-234012-MS). 🎯 Your move: keep the failed step in the lessons learned; it is what tells the next team when to switch tools.
🔵 B | Aramco and Baker Hughes: fiber pills under partial losses: torque fell 23% to 25% after fiber pills, without substantial rheology impact, across three field applications in SPE-233897-MS, where partial losses had cut effective annular velocity by 24% to 30%; the abstract reports no matched control. 🎯 Your move: run the next application against a matched untreated interval with comparable losses, effective flow rate, drilling parameters and rheology.
🟡 C (field claim 🟣 U) | A polymer mud for about 464°F: in SPE-234595-MS, China University of Petroleum (East China) reports a polymer water-based mud (WBM) whose fluid loss stayed low in the lab at about 20.0 ppg under saturated salt after 16 hours of dynamic aging; the authors say it ran in the deepest section of the SDTK 1 scientific well, without field data. 🎯 Your move: ask for the SDTK 1 mud reports before treating it as field-proven.
The first lesson: every grade A cement and repair job this month was read from the well, not from the job ticket, and each kind of evidence answered its own question. Placement records and bond logs in Norway and Hungary show the job went as designed with cement behind pipe; the Saudi casing and completion test at 3,000 psi for 30 minutes and the 300-psi squeeze tests in Indonesia show pressure containment within the tested boundary, while the 4,400-psi check confirmed the rupture disk functioned; the Hungarian stimulation stages and a Kuwaiti well that stopped making water show isolation holding in service.
The second lesson is to read the yardstick and the clock before buying the tool. Nabors' records arrive with neither a baseline nor a clock basis; Shell and SLB name a basin record built from more than 45 wells, but not how the rate was clocked.
Then find the limiter. Browse worked its limiters from the bit to solids control, while at Well 960 the study identifies integrated hydraulic limitations, with fracture filling as context rather than a demonstrated cause. The same kind of test cuts both ways: in Hungary the stimulation supported the cement, and at Well 960 the pumping test exposed the limits of the well and reservoir system.
Well 960 is an A because its authors measured that disappointment and published it.
✅ Practical Recommendations
Your checklist from this month's field evidence:
Before you design
🔀 In a narrow window, look at the returns path first. Before redesigning the slurry, check whether the casing design can route returns away from the tightest annulus. (OKEA, SLB)
🌀 Price lost lateral, not only lost hours. Compare MPD and conventional plans on the lateral each one can deliver. (Opla, Devon)
🧗 Work the limiters in order. List every limit on weight on bit and rotary speed, from the bit to surface solids control, and check that removing one does not create the next. (Shell, SLB)
Before you pump
🧪 Name the post-job check for each question. Write into the program which check accepts the job: placement records for the job itself, a log for cement behind pipe, a pressure test for the barrier, a stimulation or production check for service. Keep the pressure playback next to the log, and state the test boundary, pressure, hold time and acceptance criterion for the intended service: this month's values are case values, not a recipe. (SLB Hungary, Saudi Aramco, NESR, KOC)
💧 Screen the squeeze cement with injectivity, then qualify it. Run injectivity and leak characterization first, qualify particle size, fluid compatibility and placement pressure, and do not repeat a cement design that has already failed. (NESR)
Before you believe the number
📊 Ask for the benchmark's recipe and its clock. Who built it, from which wells, and whether time is on-bottom or total. (Nabors)
⚙️ Ask for downhole rpm, not only surface rpm. Put downhole rotary speed and the damper position by hole size into the vibration report. (Stick-slip, damper)
🔍 Read the dull alongside the rate. Judge a new cutter on its rate against named offsets, its dull condition and whether each feature engaged at the depth of cut you actually drilled. (Halliburton, Pertamina Hulu Rokan)
🪨 Refine the hydraulic diagnosis at each stage. For carbonate geothermal wells, assess hydraulic effectiveness and fracture filling with the data available at each design stage. Use post-drilling and post-stimulation multirate tests to refine the reservoir and near-well diagnosis, and establish a sustainable operating rate through longer-duration testing. (Well 960)
📩 To discuss a scoped technical review of a cementing or casing-repair program, contact WillCo Drilling Consulting: info@willcodrilling.com
Have a field result with its log behind it? Same address.
🔭 What We're Watching Next
For next month's Field Review, these are the open items:
🌋 Quaise Obsidian: a depth reached and a measured temperature from the well.
🔩 Saudi Aramco's wet shoe track: results from the next wells as the design moves toward standard use.
⚙️ The Yang 101X2 damper: a second trial well.
💎 Shaped cutters: a run in which the Shape 2 backup element engages.
🌀 Woodford MPD: a second conventional offset on the same pads.
⏱️ Nabors records: the clock basis (on-bottom or total) behind the two figures.
Follow WDI at willcodrilling.com/wdi for the weekly editions and the monthly Field Review. Grades move when the evidence does.
📚 References
E. Bye (OKEA ASA); K. Christensen, R. Stadlwieser, D. Munoz, C. Gomez, I. Gordon, J. Barreiro, J. Knowles (SLB); G. Laughton, A. Ritchie (Three60 Energy). "Making the Uncementable Cementable: An Integrated Geomechanics, Fluids, and Inner-String Cementing Strategy," SPE-233957-MS, SPE ATCE 2026, published Oct 14, 2026. DOI: 10.2118/233957-MS. https://doi.org/10.2118/233957-ms
S. Sari, Z. Gyetvai, C. R. Johnson, L. Gabilly, A. Hegedus (SLB). "Ultra-HPHT Cementing Success in Europe's Most Extreme Wells," SPE-233873-MS, SPE ATCE 2026, published Oct 14, 2026. DOI: 10.2118/233873-MS. https://doi.org/10.2118/233873-ms
O. I. Bukhari, S. S. Almasmoom (Saudi Aramco); N. Albaijan, A. Gundersen (Baker Hughes). "First Engineered Wet Shoe Track Longstring Completion in an Unconventional Carbonates Area of Interest: Field Installation and Cementation," SPE-234172-MS, SPE ATCE 2026, published Oct 14, 2026. DOI: 10.2118/234172-MS. https://doi.org/10.2118/234172-ms
Perenco UK. "Leman South and Durango subsea assets successfully decommissioned," news release, Oct 19, 2026. https://www.perenco.com/wp-content/uploads/2026/10/Leman-South-and-Durango-subsea-assets-successfully-decommissioned.pdf. Also reported by Drilling Contractor, "Perenco UK completes P&A of Leman South and Durango subsea wells," Oct 20, 2026. https://drillingcontractor.org/perenco-uk-completes-pa-of-leman-south-and-durango-subsea-wells-80390
N. P. Ananda, W. Wicaksono (NPS Energy Indonesia, NESR). "Improving the Success Ratio of Squeeze Cementing Challenges in Very Tight Formations Through Microfine Cement Technology," SPE-234406-MS, SPE APOGCE 2026, published Oct 12, 2026. DOI: 10.2118/234406-MS. https://doi.org/10.2118/234406-ms
E. AlEjel, H. M. Haif, A. J. Saleem, A. Al-Sabee, M. Al-Balool, A. Merza, J. Hassan, M. Falah (KOC); H. Gobran, A. Saleh, M. K. Dhamodharan, F. Alnajdi, N. Kumar (Weatherford). "Record-Length 9-5/8" Tubular Patch Restores Casing Integrity, Eliminates Water Production, and Revives Oil Output: A High-Value Remediation Case from North Kuwait," SPE-234528-MS, SPE APOGCE 2026, published Oct 12, 2026. DOI: 10.2118/234528-MS. https://doi.org/10.2118/234528-ms
A. A. Samo, A. Y. Sadat (Opla Energy Services); C. Jamerson, J. Coykendall (Devon Energy). "Case Study: Non-Productive Time and Mud Cost Reduction with Managed Pressure Drilling in the Woodford Shale, Canadian County, Oklahoma," SPE-233915-MS, SPE ATCE 2026, published Oct 14, 2026. DOI: 10.2118/233915-MS. https://doi.org/10.2118/233915-ms
X. Yang, Y. Jian, X. Yu (CNPC Daqing Drilling Engineering Co.); P. Yan, F. Zhang, G. Hu (Southwest Petroleum University). "Nonlinear Modeling and Multidirectional Mitigation of Coupled Axial-Lateral-Torsional Drillstring Vibrations in Deep-Well Drilling," Processes 14(21):3424, published Oct 26, 2026. DOI: 10.3390/pr14213424. https://doi.org/10.3390/pr14213424
W. Wang (Shanghai University); H. Wang, H. Zhang, B. Xu (Sinopec Research Institute of Petroleum Engineering). "An experimental and numerical study on drillstring stick-slip oscillations in ultra-deep wells," Scientific Reports, published Oct 23, 2026. DOI: 10.1038/s41598-026-76920-z. https://doi.org/10.1038/s41598-026-76920-z
L. J. Nguyen (Shell Australia); C. K. Singam (SLB Australia); M. W. Dykstra, D. Daechsel (Shell Exploration & Production Company); W. Watson, F. Bos, M. Cadd (Shell Australia); R. Procter (Ray Procter Group). "Redefining Browse Basin Drilling Performance Through Drill Bit & BHA Design," SPE-234488-MS, SPE APOGCE 2026, published Oct 12, 2026. DOI: 10.2118/234488-MS. https://doi.org/10.2118/234488-ms
A. Rebrikov, Y. Wiratomo, B. Buhron (Halliburton); R. Wijokongko, F. Nuraeni, K. Benny (PT Pertamina Hulu Rokan). "Shaped PDC Cutter Technology for Improved ROP and Durability Across Variable Lithologies: Multi-Case Asia Pacific Field Results," SPE-234561-MS, SPE APOGCE 2026, published Oct 12, 2026. DOI: 10.2118/234561-MS. https://doi.org/10.2118/234561-ms
C. Zhu, K. Li, W. Yao, W. Geng, Y. Huang, S. Jiang, N. Qiu (China University of Petroleum, Beijing; Hebei Provincial Bureau of Geology and Hydrogeology and Engineering Geology Fourth Brigade). "Post-Stimulation Hydraulic Response and Productivity Constraints of a Low-Productivity Carbonate Geothermal Well in the Small Intramontane Basin, Beijing Piedmont, North China," Energy Science & Engineering, published Oct 6, 2026. DOI: 10.1002/ese3.70668. https://doi.org/10.1002/ese3.70668
M. S. Khalaf (Independent Researcher, Houston). "Permeability Evolution and Heat Extraction in Superhot and Supercritical Geothermal Systems: From Brittle-Ductile Mechanics to Long-Term Reservoir Performance," Energies 19(19):4666, published Oct 2, 2026. DOI: 10.3390/en19194666. https://doi.org/10.3390/en19194666
Quaise. "Confirming the Resource at Project Obsidian," Oct 26, 2026. https://www.quaise.com/news/confirming-the-resource-at-project-obsidian
Nabors Industries. Third-Quarter 2026 Results, Form 8-K Exhibit 99.1, Oct 27, 2026. https://www.sec.gov/Archives/edgar/data/0001163739/000110465926119167/tm2628332d1_ex99-1.htm
Nabors Industries. Third-Quarter 2026 investor presentation, Form 8-K Exhibit 99.2, Oct 27, 2026. https://www.sec.gov/Archives/edgar/data/0001163739/000110465926119167/tm2628332d1_ex99-2.htm
Weatherford International. Third-Quarter 2026 Results, Form 8-K Exhibit 99.1, Oct 20, 2026. https://www.sec.gov/Archives/edgar/data/0001603923/000160392326000118/a2026-q3ex991earningsrelea.htm
Drilling Contractor. "CNPC recovers core at Zhentan-1 well in northwestern Tarim Basin" (core from about 26,509 ft), Oct 7, 2026. https://drillingcontractor.org/cnpc-recovers-core-from-8080-m-at-zhentan-1-well-in-northwestern-tarim-basin-80294
U. Paköz (Core Laboratories, Dammam; Middle East Technical University). "Assessing the feasibility of sidewall coring in thinly laminated unconsolidated reservoirs: insights from field operations and core analysis," Journal of Petroleum Exploration and Production Technology, published Oct 31, 2026. DOI: 10.1007/s13202-026-02254-1. https://doi.org/10.1007/s13202-026-02254-1
M. W. Powell, N. Malenovic (Welltec); L. R. Moberg, V. Haugstvedt (Equinor). "Breaking the Limits: How Wireline Solutions Conquered a Unique Coiled Tubing Fishing Challenge," SPE-234012-MS, SPE ATCE 2026, published Oct 14, 2026. DOI: 10.2118/234012-MS. https://doi.org/10.2118/234012-ms
T. Kotb, A. Gadalla (Saudi Aramco); H. Al-Arab, M. Hazem (Baker Hughes). "Advancing Drilling Efficiency Through Fiber-Driven Hole-Cleaning Strategy in Partial Loss Environments," SPE-233897-MS, SPE ATCE 2026, published Oct 14, 2026. DOI: 10.2118/233897-MS. https://doi.org/10.2118/233897-ms
Y. Sun, J. Sun, K. Lv, J. Liu (State Key Laboratory of Deep Oil and Gas, China University of Petroleum, East China). "Ultra-High Temperature Resistant and Environmentally Friendly Polymer Water-Based Drilling Fluid: Development, Performance Evaluation, and Field Application," SPE-234595-MS, SPE APOGCE 2026, published Oct 12, 2026. DOI: 10.2118/234595-MS. https://doi.org/10.2118/234595-ms
WillCo Drilling Intelligence archive: weekly editions and Field Review All Issues. https://willcodrilling.com/wdi
About this report: WillCo Drilling Intelligence - Field (WDI-F) is the monthly field track of WillCo Drilling Intelligence, published as the Field Review by WillCo Drilling Consulting. Where the weekly edition follows digital drilling, WDI-F follows physical well engineering (cement, casing, bits, abandonment and frontier drilling) and grades every story by the evidence behind it, from A (executed in the field) to U (unverified with available data). Analysis and recommendations reflect WillCo's independent engineering perspective. Imperial values marked "about" are WillCo conversions from the sources' metric units.



Comments